Mode Will Not Change From RPM to PressureĪre the PUMP ENGAGED and OKAY TO PUMP lamps on?ĭoes the MODE switch pass the I/O test? (Accessed in the Information Center menu.)Ĭheck that the proper lamps are on for the mode you want to operate. Is there an OK to PUMP indication in the cab?Ĭheck for 12 VDC at pin #10 of the EFC 12-pin connector as listed in Table.Is the transmission in the proper range for pump operation?."12-pin Connector, Deutsch DT06-12S, DDC P/N: 23520825"Ĭheck that all OEM safety requirements for pump operation are fulfilled. Press the INC and then the PRESET buttons to increase pump pressure.Ĭheck for a pump discharge pressure reading in the Menu.Įngine Data Display Is Showing All ZeroesĬheck that the connections at pins #3 and #4 of the EFC 4-pin connector, as listed in TableĬheck that there is continuity on the 900 and 901 circuits from the ECM/ECU connector to the EFC connector.Ĭheck that the transmission is in neutral, or the hand throttle (PTO) is engaged.Ĭheck for 12 VDC at pin #2 of the EFC 12-pin connector as listed in Table Throttle Will Not Increase In Pressure ModeĬheck that all three lamps: PUMP ENGAGED, OKAY TO PUMP, and THROTTLE READY are on. This is indicated on the EFC by a momentary lighting of all the display segments.) The EFC performs a "self-test" when it is powered up. (Remove power to the EFC wait ten seconds and then power the unit and try again. (Accessed in the Information Center menu.) Does the EFC indicate it is increasing RPM on the data display?Ĭheck the switch and outputs I/O test. Press the PRESET and then the INC buttons. The EFC will not respond in RPM mode unless the OEM safety interlock requirements that enable the throttle are met. "4-pin Connector, Deutsch DT06-4S, DDC P/N: 23512304"Ĭheck that the THROTTLE READY lamp is on. "Electronic Fire Commander Troubleshooting"Ĭheck that the necessary switches are turned on.Ĭheck that there is a 12 VDC between pins #1 and #2 at the EFC 4-pin connector, as listed in Table Some of the common troubles encountered during the installation and check out of the Electronic Fire Commander and suggested actions are listed in Table Price includes door to door delivery in mainland UK.įor delivery to UK islands and Northern Ireland or to arrange for a bolt down service, please call us on 01704 545400.Figure 1. ![]() Optional pull out shelves & drawers available.ĬOLOUR – Finished in a high quality scratch resistant paint RAL9003 White.įor dimensions and weight etc, please see Product Description at the foot of this page. SPECIAL FEATURES – Supplied with 3 height adjustable shelves that also includes hanging rails for lateral files as standard. LOCKING – FS1910E – Fitted with an advanced high security electronic lock with clear LED display, dual control, hidden code & scrambled code that can be programmed as standard. SECURITY PROTECTION – The safe is recommended for an overnight cash risk of £2,500.00 or £25,000.00 valuables.ĭROP TEST – Fire and impact tested from 9.1 metres for resistance to the impact of falling through the burning floors of a building. THE PHOENIX FIRE COMMANDER FS1912E offers unrivalled protection for documents, digital media and cash.įIRE PROTECTION (PAPER) – Tested to the Swedish NT Fire 017 – 120 Paper standard, providing 120 minutes fire protection for paper documents.įIRE PROTECTION (DIGITAL MEDIA) – Tested to MTC DIP120 - 60DM Fire Test standard providing up to 60 minutes fire protection for DVDs, memory sticks and hard drives.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |